Streetglow Multicolor LED Undercar Kit Manuel d'utilisateur télécharger pdf (Page 2)

Quick Test Sequence

Step 1 Unpack entire contents of packaging and check for any damaged products before moving to the testing sequence.

Step 2 Place all four LED tubes on a test bench and connect the tubes to each other.

Then, connect them to the SGMLC.

NOTE: Align arrows on the plugs to ensure proper connection.

Step 3 Using a 12v DC power source, connect the SGMLC’s RED (ignition) and YELLOW (power) wires to the

positive (+) 12v lead of the power source.

Note: DO NOT connect the BLUE (alarm) or WHITE (courtesy light)

wires for this test.

Step 4 Connect the SGMLC’s BLACK (ground) wire to the power source’s negative (-) output

Step 5 Press and hold the (POWER/MODE) button to activate all LED segments.

Note: If none of the LEDs light up, then go back to Step 3 and check your connections.

Installation Instructions

Step 1 Select a desired location for the Multi-Color LED Controller (SGMLC) and mount using the supplied

mounting hardware.

Step 2

With SGMLC mounted, connect power and ground to the SGMLC’s power harness (see FIGURE 1)

YELLOW wire = 12v battery (+)

RED wire = 12v switched ignition (+)

WHITE wire = courtesy light (+) (optional connection)

BLACK wire = ground (-)

BLUE wire = alarm (-) (optional connection)

Step 3

Select the desired locations for the LED tube placement which are away from all fuel lines,

exhaust systems, areas of extreme heat, ABS components, SRS components, any moving parts

and where lifts or jacks are used to raise your vehicle.

Note: LED tubes need to be mounted as

to the recommended configuration (see FIGURE 1)

Step 4

Using the 3/4" tube mounting clamps and the 3/4" self-tapping screws, fasten the LED tubes to

your vehicle in the recommended mounting positions (four mounting clamps per 48" tube, three

clamps per 30" tube).

Step 5

Connect the control wire(s) of each tube together. Secure the wires to your vehicle using the 3/16"

wire clamps and 3/4" screws.

NOTE: Be sure to align the arrows on the plugs and use electrical

tape (not supplied) around the secured plugs to insure a proper weather tight connection.

Step 6

Connect the control wire of the SGMLC to the control wire of the first LED tube.

Step 7

Once wiring and mounting for all components is completed, test the SGLED100MC’s modes of

operation.

Multi-Color LED Controller (SGMLC) Operation

1) Turn unit on by pressing and holding the button for 2 seconds.

2) Turn unit off by pressing and holding the button for 2 seconds.

3) To change color, press the

C (COLOR) button.

4) To change modes, press the button.

5) To change patterns, press the + or – buttons.

6) To increase brightness/speed/sensitivity, press and hold the + button.

7) To decrease brightness/speed/sensitivity, press and hold the – button.

CONTENTS:

2 - 48” LED tube

1 - 30” LED tube w/ 4' wire

1 - 30” LED tube w/ two 4' wires

1 - Multi-Color LED Controller (SGMLC)

ALARM

(-)

BLACK

WHITE

YELLOW

GROUND (-)

OURTESY LIGHT

IGNITION (+)

(OPTIONAL)

12v BATTERY (+)

BLUE

MULTI-COLOR LED

CONTROLLER (SGMLC)

(

mount under dash)

MINI DIN

CONNECTION

MINI DIN

CONNECTION

MINI DIN

ONNECTION

INI DIN

CONNECTION

FIGURE

FRONT

REAR

WIRING DIAGRAM

Modes and Features

MODES: All LEDs On / RPM / Music Interface / Scanning Patterns

Turn unit on and select the desired mode of operation by pressing the (POWER/MODE) button.

Main Functions

st press

utton

All LED’s On Mode (solid show of lights)

2nd press

button = RPM Mode (kit reacts to the sound of the engine from front to back)

3rd press

button = Music Interface Mode (dances to the beat of your music)

OTE: Use the + or – button to adjust sound sensitivity

th press

utton

Sequential Lighting Effects Mode (select from nine different lighting effects)

NOTE: To change pattern, press and RELEASE the + or – button

To increase pattern speed, press and HOLD the + button.

o decrease pattern speed, press and HOLD the – button.

Changing Colors

change colors, press the

C (COLOR) button. Yo

u may select between seven colors plus AUTO-CHANGE mode

(

cycles through all seven colors): RED, YELLOW, GREEN, TURQUOISE, NEO BLUE, CORAL, and WHITE.

(AUTO-CHANGE m

ode is indicated by a RED/GREEN/BLUE flash on the tubes).

Alarm Feature

The SGMLC’s alarm feature activates when the BLUE wire is triggered with a negative (ground) input.

This feature functions ONLY when the vehicle is off or when 12v is disconnected from the ignition

RED wire

(see FIGURE 1 for details). When the alarm feature is active, the front and back tubes will flash once per second

under the vehicle.

Courtesy Light Feature

The SGMLC’s courtesy light feature activates when the WHITE wire is triggered with a positive 12v input

(dome light circuit). This feature will illuminate the kit for as long as the door is opened.

LED UNDERCAR KIT

MULTI-COLOR

14 - 3/4" mounting clamps

12 - 3/16" wire clamps

26 - 3/4" self-tapping screws

Scanning Patterns

CLASSIC SCAN

a traditional light scan moving from the front of

the car to the rear, then reverse

PING-PONG

a continuous back and forth motion creating a

ping-pong-like effect

THE SHIFT

a 3-light bank leapfrog shift: three banks on, 6

banks on, next three banks on.

MARCHING ANTS

alternating light banks turn on to create a forward

marching motion

FILL-REFILL

fills into a solid color, then empties one by one

and reverses direction

CHERRY-PICKING

a quick fill, then “picked out” one by one and

reverses direction

DROP-IT

-IN

fills in one by one, then quickly dissolves and

reverses direction

PING-PONG FILL 1

a back and forth motion until all banks are lit,

then quickly dissolves and reverses direction

PING-PONG FILL 2

a back and forth motion until all banks are lit,

then empties one by one and reverses direction

ZIG-ZAG SCAN

a zig-zag pattern to the center and back out

1 2

WARRANTY 1
LED UNDERCAR KIT 2

Commentaires sur ces manuels

Pas de commentaire

Streetglow Multicolor LED Undercar Kit Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Streetglow Multicolor LED Undercar Kit